Paradise Road Dardanup 6236

Please call before coming to our yards as units may still be coming into stock.

Contact us on:
08 9358 1704
0417 925 919
Motor Vehicle Dealer License MD23423


Implement Hooks

A: Euro Euro implement hooks (Ø 40 mm) are the most widely used hook type. As a result, owners of many different loader makes can also benefit from our large implement range. B: SMS (Svensk Maskin Standard) These implement hooks (Ø 60 mm) are primarily adapted for Trima’s front loaders. If a Quicke loader is equipped with a Combi implement subframe Euro/SMS, it can work with both Euro and SMS implements. C: Quicke type 3 These implement hooks (Ø 25 mm) have only been used on older Ålö loaders (up to 1992) with the Quicke type 3 toolcarrier. If a new Quicke loader is equipped with a Combi implement subframe Euro/Type 3, it can work with both Euro implements and with the older type 3 implements.  


Quadrogrip is the best implement on the market for handling wrapped square and round bales. The implement arms are seated on 350 mm wide, extremely stable sliding plates, which move along the main frame. When stacking, it is possible to lock either the right or left arm, which makes for easier work. The sliding rails are replaceable and made of high-quality polyethylene, which does not require lubrication. These sliding surfaces are also vertical so that dirt cannot become trapped. This results in reduced friction, almost silent arm movements, minimal wear and a long service life.


Flexibal is a strong and very versatile implement. The 125 mm thick, rotating steel tubes are mounted on two powerful stone fork tines. The steel tubes are hydraulically adjustable sideways. When the bale is handled, the steel tubes roll carefully in under the bale. The tubes’ generous length and diameter distribute the pressure evenly over the bale. When straw or hay bales are to be transported, the steel tubes can be dismantled quickly and easily. With the tubes removed, Flexibal can also be used for pallet handling (max. 1,000 kg). As an option Flexibal can be equipped with an adjustable bale support that is installed on the back of the implement. This provides the potential to either handle larger bales or to stack bales on their ends.


Storing the bales upright on top of each other reduces the risk of air and moisture penetrating into the bales. The implement arms are housed in powerful hinged points with replaceable bushings. Both the right or left arm can be locked Independently, but there is still some mobility, making it possible to stack the bales tightly without damaging the plastic. In addition, the implement arms are designed so that it is easy to reverse out from the bale, and this is also an advantage when the bales are to be stacked tightly. The uniquely curved, rounded shape together with the 90 mm thick tubes contribute greatly to the very careful handling of both vertical and horizontal bales. Note in particular the long, curved tubes, curved in one piece with no sharp edges or welded joints. The upper tube extension is a Quicke speciality that provides significantly better support when the bales are handled horizontally.


Unigrip has a tested and proven design and a low net weight. It carries out the same tasks as Flexigrip. The choice between these two implements depends on the individual user’s work routines. Unigrip is also well suited for smaller square bales (80 x 80 – 130-160 cm). The implement arms distribute the pressure evenly over a large area, and this ensures careful handling of the bales. The tubes on the arms have a powerfully dimensioned diameter. Unigrip also has a large tube diameter and no sharp edges, so that the plastic around the bale is not damaged.


Split the bale with ease and cheaply Until now, splitting bales has entailed hard work or considerable expense. If you have a loader with dual-action lifting cylinders, you can solve the problem thanks to Silosplit. Silosplit can both transport and split bales. When you have placed the bale where it is to be split, you place the blade across the top of the bale and press down. Both straw and silage bales fall apart in two pieces, simply and smoothly without complicated extra hydraulics. It is then easy to handle the material. Silosplit is supplied with an easy-to-use blade guard to provide protection from the sharp cutting edge. Silosplit is naturally patented.

DB 4000

For safe handling of 2-4 bales. The bales are securely held between the tines and the upper section. In other words, there is no risk of dropping the bales during transport or stacking. The mast is both telescopic and hydraulic. The height of the upper section can vary from 95 cm to 195 cm.

DB 2115

Equip your front loader with 115 cm extra lifting height, so that you can stack the bales even higher. The DB 2115 is an excellent implement, particularly for those who require a high lifting height with short, manoeuvrable loaders.

Square Bale Fork

The Square Bale Fork’sfolding box section is a new and valuable safety detail. Firstly you can lock the tines in the upright position, increasing safety during transport, particularly on public roads. Secondly you get more efficient and safer handling. When unloading, the bales are pushed into place by the main frame. If unloading takes place at full height, the top bale is pushed into place with the aid of the upper section of the implement, without the long tines being pressed down into the bales. As a result, there is no risk of the bales falling back when you reverse. The Square Bale Fork can be supplied with two different frames. The 190 cm frame is suitable for long, large bales. The 140 cm frame is supplied with two tines as standard, although this number can be increased to a total of five. As optional extra equipment, the Square Bale Forks can be supplied with a back extension (for handling more bales) or a bag lifter (for handling large bags).


Perfect silage blocks in just a few seconds Silocut is a versatile and extremely reliable implement with low maintenance costs. Thanks to the hardened cutting blades at both the front edge and in the side sections, Silocut leaves a clean cut surface in the silo. This prevents the admission of air and heat generation, critical for the quality the silage. Pay particular attention to the angled side blades that cut against the sideplate of the implement back. This function, which is not an obvious feature on implements of this type, ensures maximum cutting force, particularly when the block is to be cut free. The box section is made of a hardened material that ensures good durability and a long service life. The tines are of the very best quality.